Page 154 Penn Tool Co. Precision Tooling Buyer's Guide 2019
P. 154
152
30-234-9
Drill Gages
Fractional - Wire Gages- Letter Size
• Made of heavy gage steel, machined and ground to close tolerances.
• Hole sizes and decimal equivalents steel stamped.
•
Fractional -
29 measuring holes for determining twist drill sizes
from ⁄ " to ⁄ " in ⁄ " increments. Shows drill sizes
1
16
1
2
1
64
in inches and decimal equivalents.
•
Wire Gages -
Used to gage and select the correct twist drill and
steel drill rod. Each hole shows the size number
and the corresponding decimal equivalents.
•
Letter Size -
Used to select or check drill sizes from A - Z.
Each hole is marked by letter and its decimal
equivalents from 0.234" through 0.413" diameter.
SIZES
PART NO.
PRICE
⁄ - ⁄ "
1
16
1
2
30-232-3
$31.80
#1 - 60
30-233-1
33.45
A - Z
30-234-9
33.45
MADE IN USA
14-187-9
Drill Gages
Fractional - Wire Gages- Letter Size
• Made of heavy gage steel, machined
and ground to close tolerances.
• Hole sizes and decimal equivalents steel stamped.
• Approximate dimensions: 6" x 2 ⁄ "
1 2
• Fractional increments: 64ths
SIZES
PART NO.
PRICE
⁄ - ⁄ "
1
16
1
2
14-187-9
$17.30
1 - 60
14-188-7
18.95
61 - 80
14-189-5
25.60
A - Z
14-186-1
25.60
14-180-4
Taper Gages
• For measuring ID of tubing, holes, slot widths,
flange face to face dimensions.
• Accuracy: ±0.004"
• Approximately 6" long.
MEASURING RANGE
PART NO.
PRICE
1
⁄ - ⁄ "/1 - 15 mm
32
5 8
14-180-4
$34.30
5
⁄ - 1 ⁄ "/15 - 30 mm
8
3
16
14-181-2
45.75
• For determining hole sizes in dies and other work.
• Made of tempered steel.
• Accuracy: ±0.002"
• Locking nut to secure leaves in any position.
• Graduated in thousands of an inch and 0.02 mm.
NO. LEAVES
RANGE
LENGTH
PART NO.
PRICE
8
0.100 - 0.500"
2 ⁄ "
1 2
14-184-6
$91.15
10
2 – 12 mm
64 mm
14-185-3
91.15
• For rapid, accurate checking of inside diameters of tubing.
• Thin, tapered leaves graduated in 64ths" to measure inside diameters or widths.
• Accuracy: ±0.002"
• Approximately 5 ⁄ " long x 1" wide.
1 4
NO. LEAVES
RANGE
LENGTH
PART NO
PRICE
4
1
⁄ – 1 ⁄ "
16
1
16
5 ⁄ "
1 4
14-183-8
$85.25
Taper Gages
Named "taper" gages only because
of their shape. They will not measure
the angle of the taper, only the diameter
of the tapered hole or slot. They are
quick and easy to use, very accurate
and convenient.
14-184-6
ages
g a g
es only because
hey will not measure
taper, only the diameter
ole or slot. They are
o use, very accurate
14-183-8
Drill Point Gages
• To check drills with 118º point angles.
• Sliding Head graduated in 32nds to verify equal
length of cutting edges.
• Rule graduated in 64ths and 32nds on one side;
16ths and 8ths on reverse side.
• Accuracy: ±0.008"
• Removable end clip.
• Head only fits steel rules ⁄ " wide x 0.040" thick.
3 4
DESCRIPTION
PART NO.
PRICE
Sliding Head w/6" Rule
13-967-5
$36.15
Sliding Head Only
13-968-3
19.85
13-967-5
Fillet Weld Gage
Check Fillet Welds
from
1
/ 8
" to 1"
• Heavy-duty 420 stainless
steel construction.
• Inch/decimal/metric reading.
• Accuracy: ±0.005"
• Size: 4" L x 1 ⁄ " W x ⁄ " Thick.
1
4
1
32
• Use single arc corners for determining
if the welds are concave (undersize).
• The set of seven blades come in handy
2" x 4 ⁄ " pocket case weighing only 4 oz.
1
2
DESCRIPTION
PART NO.
PRICE
Fillet Weld Gage
14-170-5
$58.25
14-170-5
30-234-9
Drill Gages
Fractional - Wire Gages- Letter Size
• Made of heavy gage steel, machined and ground to close tolerances.
• Hole sizes and decimal equivalents steel stamped.
•
Fractional -
29 measuring holes for determining twist drill sizes
from ⁄ " to ⁄ " in ⁄ " increments. Shows drill sizes
1
16
1
2
1
64
in inches and decimal equivalents.
•
Wire Gages -
Used to gage and select the correct twist drill and
steel drill rod. Each hole shows the size number
and the corresponding decimal equivalents.
•
Letter Size -
Used to select or check drill sizes from A - Z.
Each hole is marked by letter and its decimal
equivalents from 0.234" through 0.413" diameter.
SIZES
PART NO.
PRICE
⁄ - ⁄ "
1
16
1
2
30-232-3
$31.80
#1 - 60
30-233-1
33.45
A - Z
30-234-9
33.45
MADE IN USA
14-187-9
Drill Gages
Fractional - Wire Gages- Letter Size
• Made of heavy gage steel, machined
and ground to close tolerances.
• Hole sizes and decimal equivalents steel stamped.
• Approximate dimensions: 6" x 2 ⁄ "
1 2
• Fractional increments: 64ths
SIZES
PART NO.
PRICE
⁄ - ⁄ "
1
16
1
2
14-187-9
$17.30
1 - 60
14-188-7
18.95
61 - 80
14-189-5
25.60
A - Z
14-186-1
25.60
14-180-4
Taper Gages
• For measuring ID of tubing, holes, slot widths,
flange face to face dimensions.
• Accuracy: ±0.004"
• Approximately 6" long.
MEASURING RANGE
PART NO.
PRICE
1
⁄ - ⁄ "/1 - 15 mm
32
5 8
14-180-4
$34.30
5
⁄ - 1 ⁄ "/15 - 30 mm
8
3
16
14-181-2
45.75
• For determining hole sizes in dies and other work.
• Made of tempered steel.
• Accuracy: ±0.002"
• Locking nut to secure leaves in any position.
• Graduated in thousands of an inch and 0.02 mm.
NO. LEAVES
RANGE
LENGTH
PART NO.
PRICE
8
0.100 - 0.500"
2 ⁄ "
1 2
14-184-6
$91.15
10
2 – 12 mm
64 mm
14-185-3
91.15
• For rapid, accurate checking of inside diameters of tubing.
• Thin, tapered leaves graduated in 64ths" to measure inside diameters or widths.
• Accuracy: ±0.002"
• Approximately 5 ⁄ " long x 1" wide.
1 4
NO. LEAVES
RANGE
LENGTH
PART NO
PRICE
4
1
⁄ – 1 ⁄ "
16
1
16
5 ⁄ "
1 4
14-183-8
$85.25
Taper Gages
Named "taper" gages only because
of their shape. They will not measure
the angle of the taper, only the diameter
of the tapered hole or slot. They are
quick and easy to use, very accurate
and convenient.
14-184-6
ages
g a g
es only because
hey will not measure
taper, only the diameter
ole or slot. They are
o use, very accurate
14-183-8
Drill Point Gages
• To check drills with 118º point angles.
• Sliding Head graduated in 32nds to verify equal
length of cutting edges.
• Rule graduated in 64ths and 32nds on one side;
16ths and 8ths on reverse side.
• Accuracy: ±0.008"
• Removable end clip.
• Head only fits steel rules ⁄ " wide x 0.040" thick.
3 4
DESCRIPTION
PART NO.
PRICE
Sliding Head w/6" Rule
13-967-5
$36.15
Sliding Head Only
13-968-3
19.85
13-967-5
Fillet Weld Gage
Check Fillet Welds
from
1
/ 8
" to 1"
• Heavy-duty 420 stainless
steel construction.
• Inch/decimal/metric reading.
• Accuracy: ±0.005"
• Size: 4" L x 1 ⁄ " W x ⁄ " Thick.
1
4
1
32
• Use single arc corners for determining
if the welds are concave (undersize).
• The set of seven blades come in handy
2" x 4 ⁄ " pocket case weighing only 4 oz.
1
2
DESCRIPTION
PART NO.
PRICE
Fillet Weld Gage
14-170-5
$58.25
14-170-5
