Page 171 Penn Tool Co. Precision Tooling 2014 Sale Catalog
P. 171
The Pro Lathe Gage will allow you to set the height of your tools for optimum cutting
conditions. With this “Hands Free” design you simply set the gage on the cutter and
adjust the tool height until the bubble is centered in the level. This ensures the cutter
is accurately placed at the same height as the rotational axis of the spindle
•
Pro Lathe Gage will fit any Lathe.
•
Recessed design allows boring bars to
be easily set.
•
Made from 6061-T6 aluminum with red
hard anodize.
PRO LATHE GAGE
MODEL No.
02-000
Reg. $39.50
$29.95
•
Precision ball bearing and ground
bearing rod (included) are utilized to
ensure an accurate reading every time.
•
Typically installed in a collet or 3-jaw
chuck on the spindle side of the lathe
but it can also be installed in a drill
chuck on the end of the tail stock end
of the lathe
PRO VISE WORK STOP
•
Its super low profile design stays
completely below the top surface of the
vise which means that you do not need
to worry about it interfering with the
cutting tool paths.
•
It is an ideal datum surface to locate
your parts.
•
The Pro Stop is extremely versatile
allowing you to quickly position the
hardened steel contact rod in any
location you need it.
Designed to Mount on
Anglock Type Vises
•
Lathe Gage will allow you to set the
height of your tools for optimum cutting
conditions.
•
The Speedy Lathe Gage is CNC
machined to exacting tolerances from
6061-T6 aluminum.
•
Simply set the gage on the cutter and
adjust the tool height until the bubble
is centered in the level. This ensures
the cutter is accurately placed at the
same height as the rotational axis of the
spindle.
SPEEDY LATHE GAGE
MODEL No.
08-000
Reg. $24.95
$19.95
•
Tramming is the process of squaring the head of your mill to the table. Most
machinists know that if your mill is not trammed properly surface finishes will be
poor and parts will not be flat or square.
•
The
patent pending
Pro Tram by Edge Technology solves all of these problems
allowing you to tram your mill quickly and accurately.
•
To use the Pro Tram simply lower the unit down onto the table and adjust the head
until both indicators read the same number. Repeat this process for the opposite
axis and you are done.
•
The Pro Tram is also sized perfectly to fit the bed of a 6 inch vise allowing you
to tram the head to the vise instead of the table.
•
6" between centers of indicators.
PRO TRAM SYSTEM
MODEL No.
01-000
Reg. $124.95
$114.95
With Calibration
Gage & Padded Case
1/2" Shank
Model
No.
01-000
10-000
09-000
Graduation
Inch
0.001"
0.001"
0.0005"
Shank
Size
1/2"
3/8"
1/2"
Sale
Price
$114.95
114.95
134.95
MODEL No.
03-000
Reg. $79.95
$59.95
To Fit
Vise Size
6"
5"
4"
Model
No.
03-000
19-000
21-000
Price
Each
$59.95
59.95
59.95
•
Low profile design stays below the top surface of vise jaws for cutter clearance
•
Versatile design allows the 1/4" hardened stop rod to be quickly and accurately
positioned
•
Allows two work pieces to be located for increased productivity
•
Lever arm can be rotated out of the way for cutter clearance and accurately
relocated for repeat setup
•
Locate long stock with the included stop rod collar
•
Body made from red anodized 6061-T6 aluminum
PRO VISE STOP DOUBLE SIDE
Model
No.
18-000
20-000
22-000
To Fit
Vise Width
6"
5"
4"
Price
Each
$89.95
89.95
89.95
•
Fits all milling machine vises with 1/2"
- 7/8" thick jaws and 1/8" minimum
protrusion
•
1-1/8" wide body with 2 hardened steel
guide pins and large #10 clamp screw
are used to secure the unit to the vise
jaw
•
1/8" x 2" hardened stop pin is used to
accurately locate work pieces. The stop
pin is also adjustable side-to-side to
allow for cutter clearance
•
The stop pin is positioned completely
below the top surface of vise jaw to
allow for cutter clearance
•
Body made from anodized aluminum
•
8-32 non-marring flat point set screws
are used to secure stop rod
•
It features a micro stop rod that is positioned below the top surface of the vise jaws
for cutter clearance.
•
The stop rod is also adjustable side-to-side to allow space between the unit and
the work piece for even more cutter clearance.
VISE JAW STOP
MODEL No.
14-000
$24.95
•
Specifically designed to increase accuracy and minimize setup time by ensuring
the stop rod stays square to the work piece at all times.
•
This is made possible by constraining the moveable components of the unit to liner
motion.
•
The lever arm can also be rotated out of the way for cutter clearance and accurately
relocated for repeat setup.
PRO MILL STOP TABLE MOUNT
•
Versatile design allows the 1/4"
hardened stop rod to be quickly and
accurately positioned
•
Lever arm can be rotated out of the
way for cutter clearance and
accurately relocated for repeat setup
•
Non-marring 1/4"-20 nylon tip set
screw used to secure stop rod mount
without damage to lever arm
•
Base is keyed with table T-slot to
keep unit square to work piece. T-nut
included
Model
No.
16-000
17-000
To Fit
Table Slot
5/8" Slot
9/16" Slot
Price
Each
$59.95
59.95
PENN TOOL CO.
TOLL FREE 1-800-526-4956 FAX 1-973-761-1494
Page 171
2-1/4"
Diameter
The Mini Pro Tram by Edge Technology has all the same great features of the
full size Pro Tram but in a smaller package. The unit is perfectly sized for
bench-top and mini-mill machines.
•
Square the head of a milling machine and
milling vises quickly and easily
•
Simply lower unit to table and adjust the
head until both indicators read the same
•
Can be used with a sine bar or sine plate
to adjust the head to precise angles
MINI PRO TRAM
Model
No.
11-000
12-000
Graduation
Inch
0.001"
0.001"
Shank
Size
1/4"
1/8"
List
Price
$124.95
124.95
Sale
Price
$99.95
99.95
•
Calibration procedure accounts for
any error introduced by worn collets
•
Guaranteed to be equal to or better
than any other tramming method or
spindle squaring device available.
•
Indicator graduation 0.001" &
repeatability of 0.0002”
•
Includes calibration gage and
padded case
1-5/8"
Diameter
1/4"
3"
conditions. With this “Hands Free” design you simply set the gage on the cutter and
adjust the tool height until the bubble is centered in the level. This ensures the cutter
is accurately placed at the same height as the rotational axis of the spindle
•
Pro Lathe Gage will fit any Lathe.
•
Recessed design allows boring bars to
be easily set.
•
Made from 6061-T6 aluminum with red
hard anodize.
PRO LATHE GAGE
MODEL No.
02-000
Reg. $39.50
$29.95
•
Precision ball bearing and ground
bearing rod (included) are utilized to
ensure an accurate reading every time.
•
Typically installed in a collet or 3-jaw
chuck on the spindle side of the lathe
but it can also be installed in a drill
chuck on the end of the tail stock end
of the lathe
PRO VISE WORK STOP
•
Its super low profile design stays
completely below the top surface of the
vise which means that you do not need
to worry about it interfering with the
cutting tool paths.
•
It is an ideal datum surface to locate
your parts.
•
The Pro Stop is extremely versatile
allowing you to quickly position the
hardened steel contact rod in any
location you need it.
Designed to Mount on
Anglock Type Vises
•
Lathe Gage will allow you to set the
height of your tools for optimum cutting
conditions.
•
The Speedy Lathe Gage is CNC
machined to exacting tolerances from
6061-T6 aluminum.
•
Simply set the gage on the cutter and
adjust the tool height until the bubble
is centered in the level. This ensures
the cutter is accurately placed at the
same height as the rotational axis of the
spindle.
SPEEDY LATHE GAGE
MODEL No.
08-000
Reg. $24.95
$19.95
•
Tramming is the process of squaring the head of your mill to the table. Most
machinists know that if your mill is not trammed properly surface finishes will be
poor and parts will not be flat or square.
•
The
patent pending
Pro Tram by Edge Technology solves all of these problems
allowing you to tram your mill quickly and accurately.
•
To use the Pro Tram simply lower the unit down onto the table and adjust the head
until both indicators read the same number. Repeat this process for the opposite
axis and you are done.
•
The Pro Tram is also sized perfectly to fit the bed of a 6 inch vise allowing you
to tram the head to the vise instead of the table.
•
6" between centers of indicators.
PRO TRAM SYSTEM
MODEL No.
01-000
Reg. $124.95
$114.95
With Calibration
Gage & Padded Case
1/2" Shank
Model
No.
01-000
10-000
09-000
Graduation
Inch
0.001"
0.001"
0.0005"
Shank
Size
1/2"
3/8"
1/2"
Sale
Price
$114.95
114.95
134.95
MODEL No.
03-000
Reg. $79.95
$59.95
To Fit
Vise Size
6"
5"
4"
Model
No.
03-000
19-000
21-000
Price
Each
$59.95
59.95
59.95
•
Low profile design stays below the top surface of vise jaws for cutter clearance
•
Versatile design allows the 1/4" hardened stop rod to be quickly and accurately
positioned
•
Allows two work pieces to be located for increased productivity
•
Lever arm can be rotated out of the way for cutter clearance and accurately
relocated for repeat setup
•
Locate long stock with the included stop rod collar
•
Body made from red anodized 6061-T6 aluminum
PRO VISE STOP DOUBLE SIDE
Model
No.
18-000
20-000
22-000
To Fit
Vise Width
6"
5"
4"
Price
Each
$89.95
89.95
89.95
•
Fits all milling machine vises with 1/2"
- 7/8" thick jaws and 1/8" minimum
protrusion
•
1-1/8" wide body with 2 hardened steel
guide pins and large #10 clamp screw
are used to secure the unit to the vise
jaw
•
1/8" x 2" hardened stop pin is used to
accurately locate work pieces. The stop
pin is also adjustable side-to-side to
allow for cutter clearance
•
The stop pin is positioned completely
below the top surface of vise jaw to
allow for cutter clearance
•
Body made from anodized aluminum
•
8-32 non-marring flat point set screws
are used to secure stop rod
•
It features a micro stop rod that is positioned below the top surface of the vise jaws
for cutter clearance.
•
The stop rod is also adjustable side-to-side to allow space between the unit and
the work piece for even more cutter clearance.
VISE JAW STOP
MODEL No.
14-000
$24.95
•
Specifically designed to increase accuracy and minimize setup time by ensuring
the stop rod stays square to the work piece at all times.
•
This is made possible by constraining the moveable components of the unit to liner
motion.
•
The lever arm can also be rotated out of the way for cutter clearance and accurately
relocated for repeat setup.
PRO MILL STOP TABLE MOUNT
•
Versatile design allows the 1/4"
hardened stop rod to be quickly and
accurately positioned
•
Lever arm can be rotated out of the
way for cutter clearance and
accurately relocated for repeat setup
•
Non-marring 1/4"-20 nylon tip set
screw used to secure stop rod mount
without damage to lever arm
•
Base is keyed with table T-slot to
keep unit square to work piece. T-nut
included
Model
No.
16-000
17-000
To Fit
Table Slot
5/8" Slot
9/16" Slot
Price
Each
$59.95
59.95
PENN TOOL CO.
TOLL FREE 1-800-526-4956 FAX 1-973-761-1494
Page 171
2-1/4"
Diameter
The Mini Pro Tram by Edge Technology has all the same great features of the
full size Pro Tram but in a smaller package. The unit is perfectly sized for
bench-top and mini-mill machines.
•
Square the head of a milling machine and
milling vises quickly and easily
•
Simply lower unit to table and adjust the
head until both indicators read the same
•
Can be used with a sine bar or sine plate
to adjust the head to precise angles
MINI PRO TRAM
Model
No.
11-000
12-000
Graduation
Inch
0.001"
0.001"
Shank
Size
1/4"
1/8"
List
Price
$124.95
124.95
Sale
Price
$99.95
99.95
•
Calibration procedure accounts for
any error introduced by worn collets
•
Guaranteed to be equal to or better
than any other tramming method or
spindle squaring device available.
•
Indicator graduation 0.001" &
repeatability of 0.0002”
•
Includes calibration gage and
padded case
1-5/8"
Diameter
1/4"
3"
