Page 127 Penn Tool Co. Precision Tooling 2014 Sale Catalog
P. 127
PENN TOOL CO.
TOLL FREE 1-800-526-4956 FAX 1-973-761-1494
Page 127
TOOLMAKERS
STEEL CLAMP/VISE SET
•
Each is furnished with two take-up blocks that slip on
the end of the screw.
•
The blocks are held to allow a slight swivel action that
conforms the angle of the block to the shape of the
work being held.
•
There is a hole in the base of the Clamp/Vise so that
they may be fastened to a bench. Clamp/Vise are
made of case-hardened steel & are smoothly finished.
TAPER GAGE
•
This gage is specially designed for rapid, accurate
checking of inside diameters of tubing.
•
Also very useful for general gaging of slot widths,
hole sizes, setting calipers, etc.
•
This gage has thin, tapered leaves graduated to
measure inside diameters or widths from 1/16" to 1-
1/16" in 64ths of an inch. They are made of nicely
finished spring-tempered steel, approximately 1" wide
by 5-1/4" long.
HOLD DOWNS
•
The contact edges are tapered to hold the work
securely and to force it downward to the bed of the
machine or against any parallel surface.
•
They are especially useful for holding small work or
thin materials without distortion.
•
They are made of tool steel, hardened and ground.
V-BLOCKS & CLAMP
•
The V-blocks of this set are of case hardened steel for
wear resistance and may be used singly or in pairs.
•
This set includes a steel rod that passes through each
block, firmly held by friction positioning.
•
This keeps the blocks in alignment and adds
convenience for holding work with shoulders because
the shoulders can rest between the blocks.
•
Two grooves on each side of the blocks will hold the
clamp for small or large work.
•
The clamp is a steel forging, able to hold work up to
to 1-1/4" (32mm) in diameter.
SET No.
271C
$96.50
V-BLOCKS & CLAMPS
•
V-Blocks are precision ground to extreme accuracy.
•
The V's are central, parallel and square with the ends
and sides.
•
The blocks are made of steel, hardened and ground
and numbered in series so that the vees in each set
are always in alignment.
•
The blocks have a 1/4-20 tapped hole through the
sides so that they may be attached to an angle iron.
•
Each block is 1-1/4" square and 1-5/8" (40mm) long.
SET No.
278
$260.00
V-BLOCKS & CLAMP
•
Can be used on it's base, on the end or on either side.
•
The clamp is smaller than outside width of the block,
but has an adjustable side screw to support the block
and prevent tilting.
•
The V at the stepped end is at right angles to the base
and is handy for holding shouldered studs, pins, etc.
•
A clearance hole for drilling or removing dowel pins
is provided in the block.
•
The block has four 3/8-16 tapped holes, two in the
base and one on each side for attachment to an angle
iron.
MODEL No.
567
$299.95
1-15/16" V
Capacity
1" V
Capacity
1-1/4" V Capacity
Hold-Downs side view - tapered edges hold
the work securely
MASTER PRECISION
SQUARES 1-1/2" TO 36"
•
The finest precision-checking squares, not graduated.
Squareness accuracy to .0001" every 6".
•
The beams and blades are hardened, ground, and
lapped to insure parallelism and straightness.
•
The beam is grooved at the inner corner for clearance
of burr or dirt.
*Length of blade from the inner edge of the beam to the
end of the blade. Wood cases available (Inquire)
•
Made of high quality tool
steel, with the finest of
craftsmanship throughout.
•
These gages are for determining hole sizes in dies
and all kinds of other work.
•
They read in thousandths of an inch or 0.02mm.
•
Made of tempered steel with a locking device for
fixing any leaf in position for use.
.001" Graduations
.010-.150"/0.3-4mm
•
The gage is made of quality tool steel 7/16" wide by
6-1/4" long and is accurately tapered throughout its
entire length for quick and convenient measuring of
slot widths, etc.
•
One side is graduated from .010" to .150" in
thousandths of an inch and the reverse side from
0.3mm to 4mm in one twentieth of a mm (0.05mm)
V-BLOCK & CLAMP SET
2" Round & 1-7/16" Square Capacity
•
Hardened steel, precision ground parallel and square.
•
V-grooves are ground central and parallel to the
sides and base.
•
Clamps have screw holes at 45º and 90º to hold
either square or round work.
•
Stepped groove construction permits high or low
clamp mounting for small or large work.
•
Clamps do not project over the width of the block,
permitting it to be used on the base, ends or sides.
•
3/8-16 tapped holes permit mounting blocks on
faceplates or angle irons.
•
Each block is 2-1/2" long x 3" wide x 2" high (63 x 75
x 50mm).
$439.95
SET No.
568C
2"
Capacity
TAPER GAGES
TAPER GAGE
Match Pair
SET No. 160
$154.50
$115.00
MODEL No. 267
$82.25
MODEL No.
14-183-8
$87.95
.100"~.500"
MODEL No.
14-184-6
$87.95
2~12mm
MODEL No.
14-185-3
$105.00
MODEL No. 270
$81.45
MODEL No.
14-179-6
Square Size
Blade X Beam
1-1/2"x 1-1/2"
3"x 2-3/8"
4-1/2"x 3-1/2"
6"x 4-15/16"
12"x 7"
24"x 12-15/16"
36"x 20"
Straight
Blade#
20-1-1/2 $171.50 55-1-1/2 $190.00
20-3
20-4-1/2
20-6
20-12
20-24
20-36
Price
Each
180.00 55-3-1
220.00 55-4-1/2 255.00
290.00
645.00
1500.00
3750.00
Beveled
Blade#
55-6
Price
Each
205.00
295.00
Model
54A (Pair)
Length
4"
Width
27/32"
Price
$82.50
Model
269A
269B
269MA
269MB
Range
.100-.500"
.500-1"
2-12mm
12-25mm
Length
2-1/2"
2-3/4"
64mm
70mm
Leaves
8
10
10
13
Price
$126.00
148.00
$126.00
148.00
0.02mm Graduations
TOLL FREE 1-800-526-4956 FAX 1-973-761-1494
Page 127
TOOLMAKERS
STEEL CLAMP/VISE SET
•
Each is furnished with two take-up blocks that slip on
the end of the screw.
•
The blocks are held to allow a slight swivel action that
conforms the angle of the block to the shape of the
work being held.
•
There is a hole in the base of the Clamp/Vise so that
they may be fastened to a bench. Clamp/Vise are
made of case-hardened steel & are smoothly finished.
TAPER GAGE
•
This gage is specially designed for rapid, accurate
checking of inside diameters of tubing.
•
Also very useful for general gaging of slot widths,
hole sizes, setting calipers, etc.
•
This gage has thin, tapered leaves graduated to
measure inside diameters or widths from 1/16" to 1-
1/16" in 64ths of an inch. They are made of nicely
finished spring-tempered steel, approximately 1" wide
by 5-1/4" long.
HOLD DOWNS
•
The contact edges are tapered to hold the work
securely and to force it downward to the bed of the
machine or against any parallel surface.
•
They are especially useful for holding small work or
thin materials without distortion.
•
They are made of tool steel, hardened and ground.
V-BLOCKS & CLAMP
•
The V-blocks of this set are of case hardened steel for
wear resistance and may be used singly or in pairs.
•
This set includes a steel rod that passes through each
block, firmly held by friction positioning.
•
This keeps the blocks in alignment and adds
convenience for holding work with shoulders because
the shoulders can rest between the blocks.
•
Two grooves on each side of the blocks will hold the
clamp for small or large work.
•
The clamp is a steel forging, able to hold work up to
to 1-1/4" (32mm) in diameter.
SET No.
271C
$96.50
V-BLOCKS & CLAMPS
•
V-Blocks are precision ground to extreme accuracy.
•
The V's are central, parallel and square with the ends
and sides.
•
The blocks are made of steel, hardened and ground
and numbered in series so that the vees in each set
are always in alignment.
•
The blocks have a 1/4-20 tapped hole through the
sides so that they may be attached to an angle iron.
•
Each block is 1-1/4" square and 1-5/8" (40mm) long.
SET No.
278
$260.00
V-BLOCKS & CLAMP
•
Can be used on it's base, on the end or on either side.
•
The clamp is smaller than outside width of the block,
but has an adjustable side screw to support the block
and prevent tilting.
•
The V at the stepped end is at right angles to the base
and is handy for holding shouldered studs, pins, etc.
•
A clearance hole for drilling or removing dowel pins
is provided in the block.
•
The block has four 3/8-16 tapped holes, two in the
base and one on each side for attachment to an angle
iron.
MODEL No.
567
$299.95
1-15/16" V
Capacity
1" V
Capacity
1-1/4" V Capacity
Hold-Downs side view - tapered edges hold
the work securely
MASTER PRECISION
SQUARES 1-1/2" TO 36"
•
The finest precision-checking squares, not graduated.
Squareness accuracy to .0001" every 6".
•
The beams and blades are hardened, ground, and
lapped to insure parallelism and straightness.
•
The beam is grooved at the inner corner for clearance
of burr or dirt.
*Length of blade from the inner edge of the beam to the
end of the blade. Wood cases available (Inquire)
•
Made of high quality tool
steel, with the finest of
craftsmanship throughout.
•
These gages are for determining hole sizes in dies
and all kinds of other work.
•
They read in thousandths of an inch or 0.02mm.
•
Made of tempered steel with a locking device for
fixing any leaf in position for use.
.001" Graduations
.010-.150"/0.3-4mm
•
The gage is made of quality tool steel 7/16" wide by
6-1/4" long and is accurately tapered throughout its
entire length for quick and convenient measuring of
slot widths, etc.
•
One side is graduated from .010" to .150" in
thousandths of an inch and the reverse side from
0.3mm to 4mm in one twentieth of a mm (0.05mm)
V-BLOCK & CLAMP SET
2" Round & 1-7/16" Square Capacity
•
Hardened steel, precision ground parallel and square.
•
V-grooves are ground central and parallel to the
sides and base.
•
Clamps have screw holes at 45º and 90º to hold
either square or round work.
•
Stepped groove construction permits high or low
clamp mounting for small or large work.
•
Clamps do not project over the width of the block,
permitting it to be used on the base, ends or sides.
•
3/8-16 tapped holes permit mounting blocks on
faceplates or angle irons.
•
Each block is 2-1/2" long x 3" wide x 2" high (63 x 75
x 50mm).
$439.95
SET No.
568C
2"
Capacity
TAPER GAGES
TAPER GAGE
Match Pair
SET No. 160
$154.50
$115.00
MODEL No. 267
$82.25
MODEL No.
14-183-8
$87.95
.100"~.500"
MODEL No.
14-184-6
$87.95
2~12mm
MODEL No.
14-185-3
$105.00
MODEL No. 270
$81.45
MODEL No.
14-179-6
Square Size
Blade X Beam
1-1/2"x 1-1/2"
3"x 2-3/8"
4-1/2"x 3-1/2"
6"x 4-15/16"
12"x 7"
24"x 12-15/16"
36"x 20"
Straight
Blade#
20-1-1/2 $171.50 55-1-1/2 $190.00
20-3
20-4-1/2
20-6
20-12
20-24
20-36
Price
Each
180.00 55-3-1
220.00 55-4-1/2 255.00
290.00
645.00
1500.00
3750.00
Beveled
Blade#
55-6
Price
Each
205.00
295.00
Model
54A (Pair)
Length
4"
Width
27/32"
Price
$82.50
Model
269A
269B
269MA
269MB
Range
.100-.500"
.500-1"
2-12mm
12-25mm
Length
2-1/2"
2-3/4"
64mm
70mm
Leaves
8
10
10
13
Price
$126.00
148.00
$126.00
148.00
0.02mm Graduations
